PROFINET Forum

Webinar_Question

When I use the balenaEtcher to flap, I almost always get an error message that the verification did not work, is that ok?

Webinar_Question

Is there a CLI (command line interface) for automation integrated in the ART Tester? Can pass/fail results be sent to another test framework?

Webinar_Question

Is it possible to test the CDML for controllers with the GSD Checker?

Webinar_Question

Does the ETS board support DCP DeviceRole=0x03 in new firmware?

Webinar_Question

Is there any dll available for automated PROFINET testing without using ART software?

Webinar_Question

Is there a tracker for bugs?

Webinar_Question

What is your recommendation to have more than one Version of ART installed?

Webinar_Question

What do I have to consider when testing the ART of a 1-port device with regard to the MAC and the settings? How about port MAC same with interface MAC?

Webinar_Question

If the controller tests with the ETS no longer require TFPC, what is used instead to exchange the necessary information between ART Tester and DUT? What changes are required for already implemented controller tests that are based on TFPC as stated?

Webinar_Question

What is meant by 'automated comparison of test results' with respect to the CLI in ART?

Webinar_Question

Is a special PC network card needed for running the certification tests based on ETS?

Webinar_Question

Is the Siemens Simatic IPC847E/D still required for the ETS setup or is any PC with the required operating system and network card sufficient?

Webinar_Question

Will Security class I support be mandatory for PN certification?

Webinar_Question

How do I get the update for the ETS? Is it in the test bundle and for free?

Webinar_Question

When do you expect the trial bundles to become the "official" certification tool?

Webinar_Question

Will the CP1616 also be replaced for SPIRTA and the PROFIsafe Layer Tester?

Webinar_Question

Could you please share detailed information about the ETS HW used in certification?

Webinar_Question

Will the netload robustness test also be transferred to the ETS?

Webinar_Question

What is the use of APL rate limiter in ETS APL test setup?

Webinar_Question

With APL being ethernet based, do you think customers will be more concerned about cybersecurity? What is the status of PROFINET and cybersecurity?

Webinar_Question

Which evolution kit / HW you will prefer to do the PoC?

Webinar_Question

How is it possible to build switches with high port counts. So far I see 1- or 2-ports PHYs. Switch-IC with 10Mbit/s support are very rar. Do you have any advice on how to realise APl switches with high port numbers?

Webinar_Question

How are the conformance test for certification on data and power applicable to other systems than the UNH test system mentioned in the official specifications?

Webinar_Question

Can you please provide more information on the status and future plans for PROFIdrive / Encoder Profile Tester?
Are there plans to use ETS for the related tests?
In this context: Which S7 PLC exactly replaces (or in future shall replace) the CP1616? Is it S7-1516?

Webinar_Question

Do I need to wait for PROFINET Test Bundle Version 2.45 to use the ETS for precertification (because of not full migrated yet)?

Webinar_Question

To certify a PROFINET controller a file (comparable to the GSD file) is needed. Where do I get this file from?

Webinar_Question

If a PROFINET device is only produced for one manufacturer, does it still have to be certified?
And if so, who has to commission the certification?

Webinar_Question

Can an existing GSD V2.42 be extended to include a new device as of June / July 2024?

Webinar_Question

Can the ART Tester handle only the latest GSDML file version, or is it downward compatible?

Webinar_Question

Which configuration of a device is used for the certification test if the DUT is capable of many different modules/submodules? Is it always the default configuration?

Search found 123 matches

When I use the balenaEtcher to flap, I almost always get an error message that the verification did not work, is that ok

Is there a CLI (command line interface) for automation integrated in the ART Tester?

Is it possible to test the CDML for controllers with the GSD Checker?

Does the ETS board support DCP DeviceRole=0x03 in new firmware?

Is there any dll available for automated PROFINET testing without using ART software?

Is there a tracker for bugs?

What is your recommendation to have more than one Version of ART installed?

What do I have to consider when testing the ART of a 1-port device with regard to the MAC and the settings?

Controller tests and necessary exchange of information between ART Tester and DUT

What is meant by 'automated comparison of test results' with respect to the CLI in ART?

Is a special PC network card needed for running the certification tests based on ETS?

What are the requirements for the PC, operating system and network card for ETS setup?

Will Security class I support be mandatory for PN certification?

How do I get the update for the ETS? Is it in the test bundle and for free?

When do you expect the trial bundles to become the "official" certification tool?

Will the CP1616 also be replaced for SPIRTA and the PROFIsafe Layer Tester?

Could you please share detailed information about the ETS HW used in certification?

Will the netload robustness test also be transferred to the ETS?

What is the use of APL rate limiter in ETS APL test setup?

Cybersecurity

Evolution kit

Switches with high port counts

Conformance tests

Can you please provide more information on the status and future plans for PROFIdrive / Encoder Profile Tester?

Do I need to wait for PROFINET Test Bundle Version 2.45 to use the ETS for precertification?

To certify a PROFINET controller a file (comparable to the GSD file) is needed. Where do I get this file from?

If a PROFINET device is only produced for one manufacturer, does it still have to be certified?

Can an existing GSD V2.42 be extended to include a new device as of June / July 2024?

Can the ART Tester handle only the latest GSDML file version, or is it downward compatible?

Configuration of a device for certification testing with different modules/submodules.