When I use the balenaEtcher to flap, I almost always get an error message that the verification did not work, is that ok? The process should end with a successful validation. If you have this problem, please try common problem solutions. Like download bundle again, reinstall tester and try with new...

Is there a CLI (command line interface) for automation integrated in the ART Tester? Can pass/fail results be sent to another test framework? Yes, we provide an AutomatedRtTesterCli.exe. We do not provide a pass/fail in the output. To get a result please use the xml report that is provided for ever...

Webinar_Question wrote: ↑09 Sep 2024, 09:56 Is it possible to test the CDML for controllers with the GSD Checker?

There is no Checker for CDML available, as the CDML is only used in the certification test and not like the GSD files in the engineering tools.

Webinar_Question wrote: ↑09 Sep 2024, 09:55 Does the ETS board support DCP DeviceRole=0x03 in new firmware?

The ART supports devices that send DeviceRole as 0x03.
But please note, that ART does only test the device or the controller part. Not a combination.

Webinar_Question wrote: ↑09 Sep 2024, 09:54 Is there any dll available for automated PROFINET testing without using ART software?

Every Testcases is provided in a separate dll file, but these files use the API of the ART base implementation. There are no standalone dll files for testing.

Webinar_Question wrote: ↑09 Sep 2024, 09:45 Is there a tracker for bugs?

Yes, there is a bug tracker. Access can be requested via PNO office.

What is your recommendation to have more than one Version of ART installed? It is not recommended to install more than one version of ART. A parallel installation is prepared if this is intended. Like for Innovation bundles. There can be multiple versions of ART on one PC, if the installation folde...

Webinar_Question wrote: ↑09 Sep 2024, 09:44 What do I have to consider when testing the ART of a 1-port device with regard to the MAC and the settings? How about port MAC same with interface MAC?

That is no problem. Port and interface MAC have to be set, it is no problem if they are the same.

If the controller tests with the ETS no longer require TFPC, what is used instead to exchange the necessary information between ART Tester and DUT? What changes are required for already implemented controller tests that are based on TFPC as stated? There is no substitution of TFPC. With splitting t...

Webinar_Question wrote: ↑09 Sep 2024, 09:40 What is meant by 'automated comparison of test results' with respect to the CLI in ART?

The CLI of ART is capable of doing some basic comparison between two projects.

Is a special PC network card needed for running the certification tests based on ETS? For official certification a specific PC with specific network card is defined to ensure reproducible results. For in-house testing even other network cards might work but in case of issues, the specified setup is...

I followed the guide on how to create a custom power outlet for the Automated RT Tester . Unfortunately, the DLL that is created by Visual Studio can not be loaded by Automated RT Tester . It fails with the following error: ERROR: Failed to load PowerOutlet form dll. ERROR: Could not load file or a...

liaibao wrote: ↑14 Jul 2024, 08:46 I want to use python to connect to profinet devices, what python module should I use for development

I think I do not understand your question? Can you be more precise what you want to do?
Because for PROFINET, you need a profinet controller.

Hello PROFINET Forum experts. I tested our device with ART(2.44.1.2). The device has 16 electrical ports and 4 optical ports. I meet a strange problem when testing Different Access Ways Port2Port (CLRPC). The failure information of the case is shown in the attachment. The reason for the failure it ...

We at the OTH produced a video to help taking the ETS into operation. We hope it will help answering the basic questions, that appear. The video was already added to the download page of the PROFINET Test Bundle: https://www.profibus.com/download/profinet-test-bundle You can also find the video here...

Hello. We have written our own Power Outlet DLL for our test environment. Base was the template which is part of each ART Tester version. Switching dut on/off/toggle works fine. But the ART Tester does not wait (e.g. the configured DutBootUpTime / DcpResetToFactoryTestSetupTime / ...) after switchi...