Automated RT Tester / Behavior_-Scenario_10(CLRPC) failed

Ask another Question
Adam
Posts: 2
Joined: 04 Sep 2024, 10:14

Automated RT Tester / Behavior_-Scenario_10(CLRPC) failed

Post

Excuse me, seniors, I would like to ask for your advice. In the 2024-07-30_PN-Test_V2450 Test Bundle, when using the Automated RT Tester software, the test item Behavior_-Scenario_10(CLRPC) failed, but the reason for the failure is unclear. The DUT (Device Under Test) provided a get-response, and after executing ResetToFactory mode: ResetApplicationData, it reverted to default values. However, the software displays (SNMP entry: NULL). Below is the captured key packet information:
---------------------------------------------------------------------------------------------------
Frame 639: 85 bytes on wire (680 bits), 85 bytes captured (680 bits)
Ethernet II, Src: a8:bb:cc:00:00:01 (a8:bb:cc:00:00:01), Dst: 0c:73:eb:70:4a:31 (0c:73:eb:70:4a:31)
Internet Protocol Version 4, Src: 192.168.0.25, Dst: 192.168.0.50
User Datagram Protocol, Src Port: 65534, Dst Port: 161
Simple Network Management Protocol
version: version-1 (0)
community: public
data: get-request (0)
get-request
request-id: 1224599736
error-status: noError (0)
error-index: 0
variable-bindings: 1 item
1.3.6.1.2.1.1.4.0: Value (Null)
[Response In: 640]
---------------------------------------------------------------------------------------------------
Frame 640: 104 bytes on wire (832 bits), 104 bytes captured (832 bits)
Ethernet II, Src: 0c:73:eb:70:4a:31 (0c:73:eb:70:4a:31), Dst: a8:bb:cc:00:00:01 (a8:bb:cc:00:00:01)
Internet Protocol Version 4, Src: 192.168.0.50, Dst: 192.168.0.25
User Datagram Protocol, Src Port: 161, Dst Port: 65534
Simple Network Management Protocol
version: version-1 (0)
community: public
data: get-response (2)
get-response
request-id: 1224599736
error-status: noError (0)
error-index: 0
variable-bindings: 1 item
1.3.6.1.2.1.1.4.0: "Tel:123-1-1234-1234"
[Response To: 639]
[Time: 0.000799482 seconds]
---------------------------------------------------------------------------------------------------
Frame 641: 266 bytes on wire (2128 bits), 266 bytes captured (2128 bits)
Ethernet II, Src: 04:00:00:00:00:01 (04:00:00:00:00:01), Dst: Broadcast (ff:ff:ff:ff:ff:ff)
Internet Protocol Version 4, Src: 192.168.0.99, Dst: 255.255.255.1
User Datagram Protocol, Src Port: 521, Dst Port: 514
[truncated]Syslog message: USER.NOTICE: 2024/11/26 PM 02:02:45 AutomatedRtTester-Message(Interface 1): Behavior of ResetToFactory: Test step 24: The ResetToFactory mode: ResetApplicationData expects that the writeable SNMP entries are re
0000 1... = Facility: USER - random user-level messages (1)
.... .101 = Level: NOTICE - normal but significant condition (5)
Message: 2024/11/26 PM 02:02:45 AutomatedRtTester-Message(Interface 1): Behavior of ResetToFactory: Test step 24: The ResetToFactory mode: ResetApplicationData expects that the writeable SNMP entries are reset. (SNMP entry: NULL)
Top
s.zach
Posts: 18
Joined: 30 Nov 2023, 07:21

Re: Automated RT Tester / Behavior_-Scenario_10(CLRPC) failed

Post

Adam wrote: ↑26 Nov 2024, 07:57 Excuse me, seniors, I would like to ask for your advice. In the 2024-07-30_PN-Test_V2450 Test Bundle, when using the Automated RT Tester software, the test item Behavior_-Scenario_10(CLRPC) failed, but the reason for the failure is unclear. The DUT (Device Under Test) provided a get-response, and after executing ResetToFactory mode: ResetApplicationData, it reverted to default values. However, the software displays (SNMP entry: NULL). Below is the captured key packet information:
---------------------------------------------------------------------------------------------------
Frame 639: 85 bytes on wire (680 bits), 85 bytes captured (680 bits)
Ethernet II, Src: a8:bb:cc:00:00:01 (a8:bb:cc:00:00:01), Dst: 0c:73:eb:70:4a:31 (0c:73:eb:70:4a:31)
Internet Protocol Version 4, Src: 192.168.0.25, Dst: 192.168.0.50
User Datagram Protocol, Src Port: 65534, Dst Port: 161
Simple Network Management Protocol
version: version-1 (0)
community: public
data: get-request (0)
get-request
request-id: 1224599736
error-status: noError (0)
error-index: 0
variable-bindings: 1 item
1.3.6.1.2.1.1.4.0: Value (Null)
[Response In: 640]
---------------------------------------------------------------------------------------------------
Frame 640: 104 bytes on wire (832 bits), 104 bytes captured (832 bits)
Ethernet II, Src: 0c:73:eb:70:4a:31 (0c:73:eb:70:4a:31), Dst: a8:bb:cc:00:00:01 (a8:bb:cc:00:00:01)
Internet Protocol Version 4, Src: 192.168.0.50, Dst: 192.168.0.25
User Datagram Protocol, Src Port: 161, Dst Port: 65534
Simple Network Management Protocol
version: version-1 (0)
community: public
data: get-response (2)
get-response
request-id: 1224599736
error-status: noError (0)
error-index: 0
variable-bindings: 1 item
1.3.6.1.2.1.1.4.0: "Tel:123-1-1234-1234"
[Response To: 639]
[Time: 0.000799482 seconds]
---------------------------------------------------------------------------------------------------
Frame 641: 266 bytes on wire (2128 bits), 266 bytes captured (2128 bits)
Ethernet II, Src: 04:00:00:00:00:01 (04:00:00:00:00:01), Dst: Broadcast (ff:ff:ff:ff:ff:ff)
Internet Protocol Version 4, Src: 192.168.0.99, Dst: 255.255.255.1
User Datagram Protocol, Src Port: 521, Dst Port: 514
[truncated]Syslog message: USER.NOTICE: 2024/11/26 PM 02:02:45 AutomatedRtTester-Message(Interface 1): Behavior of ResetToFactory: Test step 24: The ResetToFactory mode: ResetApplicationData expects that the writeable SNMP entries are re
0000 1... = Facility: USER - random user-level messages (1)
.... .101 = Level: NOTICE - normal but significant condition (5)
Message: 2024/11/26 PM 02:02:45 AutomatedRtTester-Message(Interface 1): Behavior of ResetToFactory: Test step 24: The ResetToFactory mode: ResetApplicationData expects that the writeable SNMP entries are reset. (SNMP entry: NULL)
Hello Adam,

it is hard to identify the problem with just this information.

Please send the complete project (project file, GSD, report, pcaps and grpc logs)
to me ([email protected])
Top
Adam
Posts: 2
Joined: 04 Sep 2024, 10:14

Re: Automated RT Tester / Behavior_-Scenario_10(CLRPC) failed

Post

s.zach wrote: ↑02 Dec 2024, 08:20
Adam wrote: ↑26 Nov 2024, 07:57 Excuse me, seniors, I would like to ask for your advice. In the 2024-07-30_PN-Test_V2450 Test Bundle, when using the Automated RT Tester software, the test item Behavior_-Scenario_10(CLRPC) failed, but the reason for the failure is unclear. The DUT (Device Under Test) provided a get-response, and after executing ResetToFactory mode: ResetApplicationData, it reverted to default values. However, the software displays (SNMP entry: NULL). Below is the captured key packet information:
---------------------------------------------------------------------------------------------------
Frame 639: 85 bytes on wire (680 bits), 85 bytes captured (680 bits)
Ethernet II, Src: a8:bb:cc:00:00:01 (a8:bb:cc:00:00:01), Dst: 0c:73:eb:70:4a:31 (0c:73:eb:70:4a:31)
Internet Protocol Version 4, Src: 192.168.0.25, Dst: 192.168.0.50
User Datagram Protocol, Src Port: 65534, Dst Port: 161
Simple Network Management Protocol
version: version-1 (0)
community: public
data: get-request (0)
get-request
request-id: 1224599736
error-status: noError (0)
error-index: 0
variable-bindings: 1 item
1.3.6.1.2.1.1.4.0: Value (Null)
[Response In: 640]
---------------------------------------------------------------------------------------------------
Frame 640: 104 bytes on wire (832 bits), 104 bytes captured (832 bits)
Ethernet II, Src: 0c:73:eb:70:4a:31 (0c:73:eb:70:4a:31), Dst: a8:bb:cc:00:00:01 (a8:bb:cc:00:00:01)
Internet Protocol Version 4, Src: 192.168.0.50, Dst: 192.168.0.25
User Datagram Protocol, Src Port: 161, Dst Port: 65534
Simple Network Management Protocol
version: version-1 (0)
community: public
data: get-response (2)
get-response
request-id: 1224599736
error-status: noError (0)
error-index: 0
variable-bindings: 1 item
1.3.6.1.2.1.1.4.0: "Tel:123-1-1234-1234"
[Response To: 639]
[Time: 0.000799482 seconds]
---------------------------------------------------------------------------------------------------
Frame 641: 266 bytes on wire (2128 bits), 266 bytes captured (2128 bits)
Ethernet II, Src: 04:00:00:00:00:01 (04:00:00:00:00:01), Dst: Broadcast (ff:ff:ff:ff:ff:ff)
Internet Protocol Version 4, Src: 192.168.0.99, Dst: 255.255.255.1
User Datagram Protocol, Src Port: 521, Dst Port: 514
[truncated]Syslog message: USER.NOTICE: 2024/11/26 PM 02:02:45 AutomatedRtTester-Message(Interface 1): Behavior of ResetToFactory: Test step 24: The ResetToFactory mode: ResetApplicationData expects that the writeable SNMP entries are re
0000 1... = Facility: USER - random user-level messages (1)
.... .101 = Level: NOTICE - normal but significant condition (5)
Message: 2024/11/26 PM 02:02:45 AutomatedRtTester-Message(Interface 1): Behavior of ResetToFactory: Test step 24: The ResetToFactory mode: ResetApplicationData expects that the writeable SNMP entries are reset. (SNMP entry: NULL)
Hello Adam,

it is hard to identify the problem with just this information.

Please send the complete project (project file, GSD, report, pcaps and grpc logs)
to me ([email protected])
Thank you for your reply. I just clarified this issue and made adjustments to the stack based on the information provided by the Automated RT Tester. The test case has now been successfully passed.
Top
Ask another Question

Return to “Getting Started - Automated RT Tester”